BS EN ISO 6402-2:2003

Cross References:
ISO 62:1999
ISO 75-2:1993
ISO 178:1993
ISO 179:1993
ISO 180:1993
ISO 293:1986
ISO 294-1:1996
ISO 306:1994
ISO 527-2:1993
ISO 527-4:1997
ISO 899-1:1993
ISO 1133:1997
ISO 1183:1987
ISO 1656:1996
ISO 2561:1974
ISO 2818:1994
ISO 2897-1:1997
ISO 3167:1993
ISO 4581:1994
ISO 4589:1984
ISO 6402-1
ISO 8256:1990
ISO 10350:1993
ISO 11357-2:1999
IEC 60093:1980
IEC 60112:1979
IEC 60243-1:1998
IEC 60250:1969
IEC 60296:1982
IEC 60695-11-10:1999
EN ISO 62:1999
EN ISO 75-2:1996
EN ISO 293:2003
EN ISO 294-1:1998
EN ISO 306:1996
EN ISO 527-2:1996
EN ISO 527-4:1997
EN ISO 1133:1999
EN ISO 2818:1996
EN ISO 2897-1:1999
EN ISO 8256:1996




Keywords: Polystyrene; Thermoplastic polymers; Acrylonitrile; Plastics ; Polymers; Extruding; Moulded materials; Determination of content ; Mouldings (shaped section); Injection moulding; Moulding (process) ; Test methods; Testing conditions; Test specimens; Specimen preparation

Product Code(s): 30111744,30111744

This product references:BS EN ISO 75-2:1996 - Plastics. Determination of temperature of deflection under load. Plastics and ebonite
BS EN ISO 294-1:1998 - Plastics. Injection moulding of test specimens of thermoplastic materials. General principles, and moulding of multipurpose and bar test specimens
BS EN ISO 293:2003 - Plastics. Compression moulding test specimens of thermoplastic materials
BS EN ISO 527-2:1996 - Plastics. Determination of tensile properties. Test conditions for moulding and extrusion plastics
BS EN ISO 62:1999 - Plastics. Determination of water absorption
BS EN ISO 2897-1:1999 - Plastics. Impact-resistant polystyrene (PS-I) moulding and extrusion materials. Designation system and basis for specifications
BS EN ISO 527-4:1997 - Plastics. Determination of tensile properties. Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ISO 294-1:1996 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 2561:1974 - Plastics - Determination of residual styrene monomer in polystyrene by gas chromatography
ISO 11357-2:1999 - Plastics -- Differential scanning calorimetry (DSC) -- Part 2: Determination of glass transition temperature
ISO 4581:1994 - Plastics - Styrene/acrylonitrile copolymers - Determination of residual acrylonitrile monomer content - Gas chromatography method
ISO 2897-1:1997 - Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications
ISO 2818:1994 - Plastics - Preparation of test specimens by machining
ISO 527-4:1997 - Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ISO 62:1999 - Plastics - Determination of water absorption
ISO 1656:1996 - Rubber, raw natural, and rubber latex, natural - Determination of nitrogen content
ISO 527-2:1993 - Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics
BS EN ISO 2818:1996 - Plastics. Preparation of test specimens by machining
ISO 75-2:1993 - Plastics; determination of temperature of deflection under load; part 2: plastics and ebonite
ISO 8256:1990 - Plastics; determination of tensile-impact strength
ISO 899-1:1993 - Plastics; determination of creep behaviour; part 1: tensile creep
ISO 293:1986 - Plastics; Compression moulding test specimens of thermoplastic materials
This product replaces:BS EN ISO 6402-2:1999 - Plastics. Impact resistant acrylonitrile/styrene moulding and extrusion materials (ASA, AES, ACS), excluding butadiene-modified materials. Preparation of test specimens and determination of properties
This product same asISO 6402-2:2003 - Plastics. Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials. Preparation of test specimens and determination of properties